Tractor Talk Discussion Board |
Re: Getting rid of moles
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Richard Scott on October 17, 2004 at 20:22:28 from (64.233.107.159):
In Reply to: Getting rid of moles posted by SWMO Chris on October 17, 2004 at 19:05:22:
Lots of info on stuff that doesn't work is out there. If you use a gas engine, make sure it isn't a modern car; with the pollution controls it doesn't put out enough CO to do the job. Here's what works: Confirm the area is in use at this time by running your garden hose down thru the center of the mound into the holes and washing as much dirt as you can back into the tunnels. If this area is in use, he will push the dirt back out again in a day or so. They often have such large networks they might not come back to a particular part for weeks. You need an active area. Locate the runways by probbing with a rod or a very long screwdriver. Runways are not under the mounds; they go off to the side to push the dirt out, so the runway won't be under the mound. Get an "Out o' Sight" trap. Hop it up by grinding down the trigger mechanism (grind down the lip on the plate--you'll figure it out when you see the trap). You want the rod to slip off easily. Leave only about 1/32" of lip.
Dig into the tunnel, making a hole about 6" x 6" if you can keep it that small. Put a mound in the middle of the tunnel to make a hump--a rock works well for the hump. Being sure to keep the safety mechanism in place, set the trap in place to straddle the hump--make sure if you use a rock that the rock won't keep the trap from slicing the critter in half. Set the trap deeply enough that the critter has to go up against the trigger plate to go over your rock or mound. Undo the safety, then place a bucket over it to keep the light out. Check it frequently. Coyotes will make off with the trap if it has a mole in it--don't ask me how I know! Give it a few days in that one spot, then move on if unsuccessful. Good luck! Richard Scott
Follow Ups:
Home
| Forums
Today's Featured Article -
Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|