Tractor Talk Discussion Board |
Re: Finished the Boom, Forks and Hitch Pictures
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by T_Bone on November 19, 2004 at 04:40:14 from (4.240.39.86):
In Reply to: Finished the Boom, Forks and Hitch Pictures posted by Willy-N on November 18, 2004 at 15:02:13:
Hi Willy, I appears your about 7ft from the shackle to the point that the boom attachs to the forks. This would be calculated as a first class lever and with a 3000lb load there would be 21,000lbs applied at the boom/fork joint. 3000lbs x 7 = 21,000lbs The boom and pendant bracing would also be carrying the full 21,000lbs in compression and shear. It also appears your close to 3ft from the forks to the hanger attachments on the tractor so then you would have 30,000lbs at this point on the tractor or 10,000lbs for each of the three attachment points on the tractor if the load distributed evenly between all three points, but it doesn't. The top link carry's the weight in shear with the side stabilizers carrying in compression. Are you real sure the tractor is designed to take this type weight at the attachment points? I just pointing out some simple math that may save you from getting hurt down the road when the boom and attachment points fail. To get a better prespective on what I'm saying lets look at a typical backhoe boom. A typical full 24" bucket carry's approx. 320/lbs of earth and will have a boom size of 6" wide x 14" deep of a tubular design. Thats with a approx 9ft boom reach. So were talking about 2900lbs at the boom attachment point at the stabilizers. The stabilizers (out riggers) remove alot of the 2900lbs of load applied to the tractor backhoe attachment points. Anyone that has ran a backhoe will agree, you never walk (travel) with load weight on the boom as you will quickly tear the boom up. From that do you really think your 2" x 2" tube boom will carry 3000lbs ? T_Bone
Follow Ups:
Home
| Forums
Today's Featured Article -
Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|