Tractor Talk Discussion Board |
Re: OT: Chevy Suburban
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by jdemaris on January 04, 2005 at 06:10:00 from (209.23.28.217):
In Reply to: OT: Chevy Suburban posted by TractorMike on January 03, 2005 at 16:14:04:
I did my 87 diesel 4WD 3/4 ton Suburban over about 8 years ago. It was a complete rust bucket and had been driven in the winter salt every year until I did it over. I bought it from my neighbor, the original owner for $500 - which at the time I thought was a bargain. Now, I take it off the road in the winter. I found that some parts are not available new, e.g. the rear quarter panels. I wound up going to a junkyard and cutting some off a non-rusted Suburban. In retrospect, it would have made much more sense to buy an entire Suburban from down south (I'm in central New York State). I had to replace all the fuel lines, brake lines, AC lines, outer-inner fenders, all the doors, sills/rockers, etc. What a mess. I've also noticed that Suburbans and K5 Blazers are particularly prone to gather salt over the rear wheel wells and quarters unless you install some sort of guards. JC Whitney used to sell formed PVC liners and they work great. Problem is, I don't think they're available anymore. Last year I purchased a 90 diesel 4WD 3/4 ton Suburban at an auction for $900. It is from Long Island NY (that's south to me) and is rust-free. Runs perfect but has no title. I'm keeping it "in stock" until I'm ready for it. I'm not sure if I'm going to strip it, or attempt to retitle it. I don't think I'd ever attempt to completely redo a rusted Suburban, it's a big vehicle. I am, however, very pleased with how mine turned out. It now has 470,000 miles on it with the original engine (never been apart). A few rust blisters are beginning to show, and at 470K miles, although it starts and runs great, I don't expect it to last much longer and am somewhat hesitant to take it cross-country.
Follow Ups:
Home
| Forums
Today's Featured Article -
Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|