Tractor Talk Discussion Board |
Re: loft in shop
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Mark - IN. on January 22, 2005 at 17:01:49 from (205.188.117.7):
In Reply to: loft in shop posted by Dan 57 on January 22, 2005 at 07:49:00:
I just built a tool shed on a 5.5" slab that is 8x24, and started out to be 10' tall, but by the time put down 4 2x4s across the bottom and 3 across the top under the trusses, is closer to 11' tall. Is pretty tall. I put 4x8' lofts on both ends just above the doors, and one big one thats 8x8 in the middle. That way have about 4' open between the lofts at either end. That leaves me about 3' of loft space under the trusses. Since are the same width as the shed, my 2x4x8's are nailed into each of the wall 2x4x10's that the edges butt up against. At each end where meet the walls, brought down 2' long 2x4's on angles for additional support under each loft support. I thought about adding hangers as well, but thought better of having the weight pull down the roof trusses, although may not have. I'm 24" centers on the walls, so is pretty stiff. I'm a big fan of screwing that kind of stuff together, but for time (needed to get up), I settled for using 3" nails and a Bostich nailer. I figure with only 3' of loft space, not likey I'm gonna put anything real heavy up there, but would probably support it. If you use 2x4's across your 12' wide, and go into each of your wall studs that butts up against, you'll be surprised at strength once nail down 1/2" or better plywood shelving. 2x6's would be even stronger. I thought being 11' high was tall, now wish had gone taller. Make sure your walls are anchored good in your slab. Steel roof is kind've expensive at first thought, but will pay for itself in the long run, and is only hard to work on if have saw dust on it, or temps dip near freezing - then is like sking without poles - make sure no shovel handles or fence posts sticking up down below, because they hurt bad. Mark
Follow Ups:
Home
| Forums
Today's Featured Article -
Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|