Tractor Talk Discussion Board |
Re: series/parallel switch
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by jdemaris on April 12, 2005 at 20:28:12 from (209.23.29.88):
In Reply to: Re: series/parallel switch posted by Jon H on April 12, 2005 at 16:25:15:
In regard to the troublesome 24-12 neg-12 pos system that Delco built for Deere. Deere lacked confidence in the capabilities of 12 volt starters at the time for use in diesels. So, they used the covoluted system. It would of been much more reliable with the series-parallel switch or, just a straight 24 volt system all the way. But, now - to install the switch into a tractor almost would not be worth the effort. I guess you could install a ground into the starter and make it a conventional 24 volt unit. You'd then have to rewire half the 12 volt system, since 1/2 the tractor is 12 volts positive ground, and the other half 12 volts negative ground. And, once you've got it all with the same polarity, you need to install - I assume - a 12 volt alternator. Seems after all that, it would be just as well to just make the whole thing 12 volts and be done with it. On a slightly different note, I've been thinking of installing such a switch on some of my 6 volt tractors that I use in the winter. I'd like to keep them somewhat original (6 volt generator and lights), but they're pretty hard to get started when it's 20 below zero F. I've been cheating and just sticking in 12 volt batteries every winter. They start great that way. I pull the light fuse out, and unhook the charging system. No big deal, but I have to charge the batteries once in awhile. Every spring, I put the 6 volt batteries back in and hook everything up again. But, maybe putting the switch in and dual 6 volt batteries is just as convoluted as changing over to a full time 12 volt system - we'll see.
Follow Ups:
Home
| Forums
Today's Featured Article -
Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|