Tractor Talk Discussion Board |
Restrictive Diesel Exhaust Problem
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txgrn on April 25, 2005 at 16:37:17 from (209.151.113.145):
One has to pay attention to what they are doing; like one thing at a time. I recently changed the muffler on my 3 cyl Ford diesel. Didn't run it much afterwards; just enough to see it was as loud as the one that had just fallen off. Parked tractor. Everything seemed ok. Came time to bale hay a few days later. Cranked up the tractor and everything seemed normal; wasn't paying much attention. Hooked on to the square baler. This tractor has independent PTO and the lever is an ON OFF sort of thing, not a variable engagement like on Deere. Had checked the baler and knew it was ready, but this was the first running of the season. Idled the tractor and engaged the PTO. The PTO snapped the baler into operation. Now for those that have never run a square baler, there is about a 500# flywheel on the crankshaft that drives the piston of the baler that crams the hay into the compression chute. Actually the tractor's job is to turn the flywheel and it drives the ram. So here I am trying to take that mass and get it going a couple hundred rpm's in a second......not good on the equipment. Well I didn't like this at all and wasn't sure that I didn't hurt something cause there were some "sounds" when it started running. Don't remember everything too well, but the tractor was missing most of the time I was baling and blowing a bluish smoke. Stack had been clean a few days earlier and was running like a top. Lost some sleep last night. Thought I might have bent a connecting rod or broke a piston ring on the tractor when the baler came to life. Since we had been talking a lot about engine exhausts lately, and restrictive or not, I decided that when I got up this morning I was going to take the new muffler off and see what happened. Did so, engine coughed and sputtered and within a few minutes was running clean as a whistle, no smoke, and no missing. HOT DIGGDY DOG!! Didn't hurt it. Put the muffler back on and back to the coughing and smoking. Took it off and looked inside and it had a baffle with a reduced diameter hole in it to make the exhaust go thru the muffle part. Apparently that was more restriction than the Ford wanted. Knocked the baffle out and put it back on and worked fine. It's obvious that this little engine did not want back pressure. The muffler wasn't Ford OEM. I went to TSC and found one that'd fit my exh pipe and had a lot of muffler area. Was for a MF. Guess MF can tolerate back pressure. Didn't have a Ford in stock and I was looking for a quieter muffler anyway. So, live and learn.
Mark
Follow Ups:
Home
| Forums
Today's Featured Article -
Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|