Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: check row planter ?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Delbert from Lincoln on May 16, 2005 at 13:49:56 from (205.188.117.74):

In Reply to: Re: check row planter ? posted by Delbert From Lincoln on May 16, 2005 at 11:53:01:

Its been about 60 years since I cultivated checked corn, but its an experience I'll never forget. F-12 Farmall, on steel, manual lift lever on each side for 1/2 the cultivator. Also the cultivator was hooked to the front steering bolster so it shifted to left or right slightly when you steered the tractor and made the steering wheel turn that much harder. When I came to the end of the row, I had to push in the clutch, take tractor out of gear, let clutch off, stand up to get enough strength to lift the cultivator out of the ground., one side at a time. Then set down, push in the clutch, put tractor in gear, let out clutch, turn around, repeat above to get cultivator back in the ground. Then there were the cross washes in the field, usually deeper then the previous cultivator marks, and usually at an angle so that one front wheeel droped in before the other one and tried to break your shoulder, then the other front wheel droped in and twisted you back the other direction. Did I remember to mention that steering wheel was a solid cast iron one, not a bit of rubber grip to it. I'm old and crippled now and in a wheel chair most of the time, but I don't miss the good old days at all. Oh yes, throttled down going thru that last cross ways ditch, didn't get the throttle open again quick enough, engine stalled and had to get off and crank it.


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Ferguson System Principal An implement cutting through the soil at a certain depth say eight inches requires a certain force or draft to pull it. Obviously that draft will increase if the implement runs deeper than eight inches, and decrease if it runs shallower. Why not use that draft fact to control the depth of work automatically? The draft forces are ... [Read Article]

Latest Ad: 1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952 [More Ads]

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy