Tractor Talk Discussion Board |
Re: 706
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by the tractor vet on May 19, 2005 at 08:17:05 from (4.124.73.195):
In Reply to: 706 posted by jack swanson on May 19, 2005 at 04:38:05:
Well , first of adjusting linkage is not going to solve anything . Parts are wore out or broken and ya don't have to spend 600 bucks for someone idea of his snakebite oil. I ahve fixed so many that i can do it in my sleep . Step ( 1) remove the cowel and see how much ware is in the top linkage as i call them the CUB CADET TIEROD ENDS replace them next replace the headed pins on the shift linkage down by the top of the trans cover and get the correct pins not will fit because the cotter pin hole are alwayin the wrong place or make the pins if ya got a lathe . (2) check and see how much play is in the top cover shift lever , you will probably find that the pin that hold the cam to the lever is broken and the keyway is wore out replace shift lever and sometimes the cam and a new key . (3) check for lost or broken rollers the cover must come off this is when a freind is helpful (1)st remove the side cover on the rear end housing by the left step that cove exposes the rev. shift fork you will lose about a gallion of hdy oil the shift rod for rev will come out with the top cover this is also when a second set of hands is helpful don't lose the littel key on the rev shift lever as it is also part of your problem as you raise the top cove the rev. shift fork will fall out and the key will fall out . You can fix it all for less then that snake oil kit . But if ya want to spend money ship it to me and i'll fix it for 450 bucks plus transportation charges and it will shift like a new one . the biggest problem with them is that the clutch get out of adjust ment and people start jerking on them and things start getting ugly when everything is the way it should be they will shift with two fingers. Got problems call me 330-337-8113 after 9pm ohio time . the tractor vet.
Follow Ups:
Home
| Forums
Today's Featured Article -
Usin Your Implements: Bucket Loader - by Curtis Von Fange. Introduction: Dad was raised during the depression years of the thirties. As a kid he worked part time on a farm in Kansas doing many of the manual chores. Some of the more successful farmers of that day had a new time saving device called a tractor. It increased the farm productivity and, in general, made life easier because more work could be done with this 'mechanical beast'. My dad dreamed that some day he would have his own tractor with every implement he could get. When he rea
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|