Tractor Talk Discussion Board |
Re: Here's the deal
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by R. John Johnson on June 01, 2005 at 19:04:39 from (205.200.43.245):
In Reply to: Here's the deal posted by Allan in NE on June 01, 2005 at 06:17:36:
Allen My personal preference in round balers is the New Holland roll belt balers. The belts and the rollers form a chamber like a fixed chamber baler to ensure the bale core forms and starts rolling. The belts then move out under spring/hydraulic pressure to form the rest of the bale. They have two types of twine wrapping controls. Autowrap is just that. When the bale is full size a clutch engages and swings two twine arms in to wrap the bale. A buzzer goes off in the cab to alert you. When the wrapping is complete the buzzer sounds again to let you know you can eject the bale. Bale Command has a monitor with a screen . All sorts of fancy bells and whistles. There is a spring loaded ramp on the back that moves the bale back so you can close the tailgate without having to drive ahead. I bought a 664 last year after my 605 Super F burned. Best I did with the Vermeer was 85 bales in 6 and a half hours. The 664 did 148 bales in the same amount of time. The Vermeer was a good baler, but was old enough it was not designed for modern levels of capacity. My cousin has a 660 baler. Bought it the first year they came out. It has seen some tough use and a lot of bales. Never spent an hour in a shed. Minimal breakdowns and the original belts still look new. That baler is the reason I bought mine. Can't speak from experience on JD or newer Vermmer balers, but I have been told they are good. Most modern balers are very easy to operate. Many farms have the husband using the MoCo to cut and the wife bales. The better half usually has less experience with machinery so they get the easier job, which is baling. My two cents John
Follow Ups:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|