Tractor Talk Discussion Board |
Re: pointless ignition kit?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txgrn on July 13, 2005 at 06:17:20 from (209.151.114.22):
In Reply to: pointless ignition kit? posted by weaktruk on July 12, 2005 at 21:24:26:
The points (2 screws) and the condenser (1 screw) are removed.....save for a rainy day; no joke. The correct unit drops right in (where they were) and a black plastic (covered magnet) drops in over the square of the shaft (that made the points open and close. Everything else goes back together like it was except the wiring (explanation following). The black wire goes where the old dist wire went (low side of coil) and the red wire to voltage 6v or for 12v units, 12v. Be sure that you use a resistive ignition circuit of at least 3.5 ohms. Some coils made for 12v are that and some are only 1.7 (originally made for 6v systems) which require a 1.7 ohm (external) resistor in series with the coil to operate on 12v. If you don't have adequate resistance to limit the switching current to a max of 5 amperes you will burn out the electronic switch...BTDT If you have a 3.5 ohm coil, you can wire your red wire to the hot side of the coil thus getting your correct operating voltage. If you have a 6 v coil (1.7 ohms) on a 12v ignition system, you have to have a "ballast" resistor somewhere (should already be installed) and you need to go to the hot side of that resistor (not dist side) to pick up your 12v for the red wire. If you connect it to the coil (with a system using a resistor) it will only have 6 volts, from which to operate, and it will not work satisfactorily. HTH. Mark
Follow Ups:
Home
| Forums
Today's Featured Article -
Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|