Tractor Talk Discussion Board |
Re: building a shed w/tarps
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by T_Bone on August 10, 2005 at 08:23:48 from (4.240.42.217):
In Reply to: building a shed w/tarps posted by Poor guy on August 09, 2005 at 12:20:19:
Hi PG, I think the tarp idea is a waste of money as it won't last long in the wind. Me, I would spend the same money on metal track (use for all framing including studs)( no metal studs, very thinn gauge) as there a heavy gauge and will last. Then use 28ga corragated sheeting for the roof and walls until you reach the same dollar value as the tarp cost. Example: 10ft wide x 12ft long x 10ft high, 1 open end 23- metal framing track 2x4x10ft= $46 23- 2ftx10ft 28ga sheeting = $276 Box #7 x 3/4" metal screws= $5 tin snips= $15 Total= $342 at HD prices for a all metal shed, less door, door $100 more. Have a hill side? Free shed for the digging and scrap lumber. Build a sod shed. Turn a 10ft square of dirt. Mix dirt and 6" of Water and let stand. The next morning skim off the clay and set aside, then water 6" again, mix and let sit, skim off the clay. Repeat for enough clay. Now mix 14% clay by volume, dirt, pea gravel and straw. Pour that mix into blocks and let sun dry. Build shed walls with the blocks laying flat. To build the roof, pour 8" x 12" x 4" thick blocks. Start on each corner by using blocks layed flat, then use a mortar mix of 14%clay and sand to build up a taper bed for the next block and lay the next block to the inside by 1/4 of block width, continue with the next layers until the blocking is layed on the 4" edge on all four coners. You should now have a open dome roof. Use the blocks on the 4" edge to finish the open dome. Finish the roof with a mortar mix of 14% clay sand mix. To water proff inside and out, use diesel to fire blast the inside of the building to 2000º for 24hrs, about 25gal of diesel required. I won't go into details on the homemade burner but just pipe fitting and a ball valve with a 55gal drum 10ft in the air. T_Bone
Follow Ups:
Home
| Forums
Today's Featured Article -
A Cautionary Tale - by Ian Minshull. In the early 1950s my father bought an Allis Chalmers B and I used it for all the row crop work with the mangolds and potatoes, rolling and the haymaking on our farm. The farm and the Allis were sold and I have spent a lifetime working on farms throughout the country. I promised myself that one day I would own an Allis. That time event
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|