|
Tractor Talk Discussion Board |
O/T, Pole Barn
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Treeman on October 04, 2005 at 07:57:32 from (165.247.66.140):
Has anyone had good luck covering a dirt floor under a pole barn to cut down on dust. Mine is about 40 square feet. Posts are set in concrete. Covers my tractor, tools, fertilier, etc. Too expensive for a concrete slab. Thought about pine bark. Ideas?
Follow Ups:
- Re: O/T, Pole Barn Forester 17:51:45 10/05/05
(0)
- Re: O/T, Pole Barn Jim in Michigan 07:11:00 10/05/05
(0)
- Re: O/T, Pole Barn Tim...Ok 05:01:48 10/05/05
(0)
- Re: O/T, Pole Barn dave from MN 18:42:11 10/04/05
(0)
- Re: Question sq footage upred 18:24:35 10/04/05
(0)
- Re: O/T, Pole Barn Midwest redneck 16:57:14 10/04/05
(0)
- Re: O/T, Pole Barn marlowe 16:28:21 10/04/05
(1)
- Re: O/T, Pole Barn thejdman01 13:18:54 10/04/05
(0)
- Re: O/T, Pole Barn thejdman01 13:18:53 10/04/05
(1)
- Re: O/T, Pole Barn Mike Van 12:37:20 10/04/05
(0)
- Re: O/T, Pole Barn james2 09:22:27 10/04/05
(0)
- Re: O/T, Pole Barn DitchWI 09:08:08 10/04/05
(0)
- Re: O/T, Pole Barn RustyFarmall 08:54:18 10/04/05
(0)
- Re: O/T, Pole Barn steve_ne 08:44:40 10/04/05
(1)
- Re: O/T, Pole Barn Treeman 08:36:16 10/04/05
(0)
- Re: O/T, Pole Barn dhermesc 08:35:38 10/04/05
(2)
- Re: O/T, Pole Barn Not me, someone else 08:03:19 10/04/05
(0)
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
