Tractor Talk Discussion Board |
Re: Winterizing tips ?
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by John T on October 09, 2005 at 09:37:14 from (66.244.90.98):
In Reply to: Winterizing tips ? posted by MN Bob on October 09, 2005 at 08:42:12:
Just how cold does it get that far Noth Bob lol?? Do the terms Well Diggers ... or Witches ... or Brass Monkeys ... come into play lol Heres my thoughts, this is always a good question to hear how others do this, great topic considering its October
1) When I change n flush anti freeze, I been using distilled water cuz I figure its got less rust or iron or calcium etc which may coat the radiator. I add water pump lube and pre mix it 50/50 (anti freeze/water) before refilling.
2) As far as gas, I use Sta Bil (to reduce gum n varnish settling out) PLUS mix a lil bit of low ash 2 cycle oil (think it may leave a thin film oil coat n may reduce rusting inside the carb),,,,,,,,I run that witches brew a lil to coat the carb but then then I drain the carb but I prefer the gas tank be kept full to reduce condensation plus theres less air in contact with the tanks sheet metal so less rusting 3) Its good to use a trickle charge battery maintainer if left out in the cold, otherwise I would store them indoors and maybe still give em a lil trickle charge now n then. Have them topped off with electrolyte 4)) Its good to remove the plugs n squirt some oil in the cylinders n crank her a lil to oil coat the cylinders 5) I prefer to leave the points in the OPEN position (may take plug removal so no compression to get em there) 6) I dont like the tires on wet ground, maybe use blocks or rubber as insulation. Actually its even better to exercise them now n then or at least crank her over now n then to exercise the valves etc. Im also a believer in running Marvel top oil lube in the oil for valve system protection. John T, your neighbor to the tad warmer southern Indiana
Follow Ups:
Home
| Forums
Today's Featured Article -
Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|