Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: PTO seal on a TO 35


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by txgrn on October 11, 2005 at 05:32:02 from (209.151.118.68):

In Reply to: PTO seal on a TO 35 posted by BobinKY on October 10, 2005 at 18:50:19:

Just went outside and looked at my MF-35 and it has a 4 bolt retainer just like Ford.....familiar with the Ford which should be similar.

Drain the fluid first. MF uses a single cavity for tranny, hyd, and diff so you will have to collect roughly 10 gallons of oil.

Removing the 4 bolts holding the retainer which supports the shaft should allow you to pull the shaft straight out the rear. May need to help it along if it has been in there for awhile which is probably the case. It should be sealed to the housing with a large O-ring which will become visable as the assembly is removed from the tractor.

On the shaft should be a snap ring (inside)and the shaft support bearing should be jammed up against it. On the back (outside) of the bearing, on the shaft is a collar which the seal rides on and is pressed onto the shaft keeping the bearing up against the small snap ring. If this collar is not holding the bearing against the small snap ring replace it as any lateral movement of the bearing up and down the shaft allows for the PTO to disengage under load.

The bearing is held to the retainer by a large snap ring. Removing it should allow you to remove the bearing and shaft and give you access to the rear of the seal. Then it"s just a matter of knocking it out and pressing (hammering) in a new one in from the rear.

A new O-ring on the retainer and back in she goes.

Don"t forget to replace the oil or reinstall what you had if it is clearish, not milky and yellowish or just plain dirty.

Mark


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Listening to Your Tractor - by Curtis Von Fange. Years ago there was a TV show about a talking car. Unless you are from another planet, physically or otherwise, I don’t think our internal combustion buddies will talk and tell us their problems. But, on the other hand, there is a secret language that our mechanical companions readily do speak. It is an interesting form of communication that involves all the senses of the listener. In this series we are going to investigate and learn the basic rudimentary skills of understanding this lingo. ... [Read Article]

Latest Ad: 2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy