|
Tractor Talk Discussion Board |
Re: New Kid on the block: Why is live PTO importan
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by john d on November 12, 2005 at 18:30:54 from (69.128.204.56):
In Reply to: Re: New Kid on the block: Why is live PTO importan posted by Joe Hill on November 12, 2005 at 17:28:06:
Not really. The pto in either setup may be operated with or without forward movement. In the "live pto" setup, the power is always available to be applied to the pto whenever the tractor engine is running, by simply pulling the lever.
In the "non-live" pto arrangement, the power is available when the engine is running and the clutch is not depressed or dis-engaged. In order to engage the pto, the clutch pedal must be pushed, then the pto shifted into operation. The pto will not start unless the clutch pedal is released.
In the "non-live" setup, you can have the pto running with or without forward motion, but you can't stop forward motion and leave the pto running. If you stop the forward motion with the clutch, the power to the pto is also stopped. The hazard some have mentioned with this system is the tendency of a large rotating mass such as a bush hog mower to keep rotating when you push the clutch. The clutch dis-engages the engine, but since the transmission gears and pto are all driven by the same shaft, the pto will drive the transmission gears if the pto and whatever it's hooked to keep rotating. You can solve this problem by adding an "over-running" clutch at the end of the tractor pto shaft. They cost about $50 or so. This item will let the implement keep rotating but will not allow power to be returned to the tractor by the pto shaft.
For running a log splitter, a post hole auger, or a grain elevator, either pto system will work fine. For applications where you might want to interrupt forward motion while leaving the pto runing - as with a hay baler, live pto is far superior. Live pto also allows starting or stopping the implement as needed without interrupting forward motion.
The two arrangements are essentially the pto equivalents of the live, and non-live hydraulic systems.
Follow Ups:
Home
| Forums
Today's Featured Article -
Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
