Tractor Talk Discussion Board |
Re: 6v vs 8v battery
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by John T on April 18, 2006 at 06:15:32 from (66.244.90.5):
In Reply to: Re: 6v vs 8v battery posted by Leroy on April 18, 2006 at 05:46:53:
Leroy, You are absolutely correct, if a Voltage Regulator has ONLY current control relay, they will charge fine NO MODIFICATIONS REQUIRED nor would a Cutout Relay require modifications. Its the Voltage Regulators that have VOLTAGE CONTROL RELAYS that must be adjusted to work properly at 8 volts. Some VR's have only current control (2 coils, cutout relay plus current control relay), others current PLUS Voltage (3 coil relays), others have a combined curent and voltage control coil (2 coils). So long as you have the correct VR or a Cutout Relay, they will charge fine. On the coil, if you increase current through them by increasing their input voltage (8 instead of 6) since I = E/R and Power = Volts x Amps, the heat they dissipate MUST INCREASE or we have violated the laws of thermodynamics and physics. However, it may well not be noticeable from looks or a hand touch as its not all that much of an increase, but it MUST AND WILL RUN WARMER if its voltage and resulting current is increased. On the points, they are a mechanical current switching device and the same laws of thermodynamics and physics still apply. With more current passing through them and being switched and the accompanying arcing, their life must be shortened somewhat since its the current and heat and arcing that eventually destroys the conductive silver coating. Its indeed true if you increased the current passing through the coil (which the points switch) you increase the coils stored energy which eventually gets discharged across the plugs gap for a HOTTER HIGHER ENERGY GOOD BLUE SPARK. If you applied 12 volts on tha 6 volt coil the spark would even grow stronger UNTIL THE POINTS BURNED UP AND/OR THE COIL OVERHEATED AND WAS RUINED !!!!!!!!!! Fun discussion yall, hope this helps your understanding Thanks n God Bless John T Nordhoff in Indiana, retired Electrical Engineer
Replies:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|