Tractor Talk Discussion Board |
1948 Farmall Cub - Exhaust manifold overheating/sm
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Dave from York Haven PA on August 11, 2006 at 07:00:27 from (12.108.117.125):
I've been having power drop off problems on my 1948 Farmall Cub. Spark Plugs have been replaced, and I just now replaced the distributor cap and spark plug wires, because they were pretty badly corroded. I have a condensor replacement, but haven't installed that yet-kind of intimidated by that repair right now. Anyway, after I installed the wiring, which went without problems, I replace all (5) one at a time (4 plugs + main). I know from the doc that the firing order is 1-3-4-2, and I'm assuming the cylinders are numbered sequentially 1 to 4 from front to back(can someone verify 1-to-4 front to back please. If I trace the wiring from the distributor cap starting at the top (1) position, the spark plug wires run 1-3-4-2. Now my concern: When I crank start the tractor (battery needs replaced), it fires up and runs fairly smooth. After about 5 minutes, I notice 'fumes' or 'smoke' or thin, veiled vapors coming up from the engine's exhaust manifold up the outside length of the exhaust pipe (I have a vertical exhaust). Is this gasoline vapors that haven't been ignited and will they eventually ignite while running the tractor? I haven't seen any doc on this condition and how to correct it. It never did that before. I just think maybe something is not right with the firing order. I had removed the rotor once when I found the old distributor cap was corroded, but I thought I put it back in place the way I had found it, but I guess it's possible the teeth on the underside of the gears my not be exactly right. When I had removed it the one time, I had the tractor in gear so that nothing would move, because I was scared. I was trying to figure out how to replace the condensor. Is this thin wispy vapor problem the result of a timing problem? Please advise when you can...this is beyond me. I am not a mechanic, but I need to cut grass-now hay-soon, and I need my baby back in good health. Thanks ahead of time, Dave Rhan (717) 541-7176
Replies:
Home
| Forums
Today's Featured Article -
Tractor Profile: Farmall M - by Staff. H so that mountable implements were interchaneable. The Farmall M was most popular with large-acreage row-crop farmers. It was powered by either a high-compression gas engine or a distillate version with lower compression. Options included the Lift-All hydraulic system, a belt pulley, PTO, rubber tires, starter, lights and a swinging drawbar. It could be ordered in the high-crop, wide-front or tricycle configurations. The high-crop version was called a Model MV.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|