Tractor Talk Discussion Board |
Re: modern engine oil
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Hal/WA on September 01, 2006 at 15:04:09 from (66.45.175.118):
In Reply to: modern engine oil posted by mmidlam on September 01, 2006 at 07:47:18:
I read an article in one of the hot rod magazines a few months ago on this subject. They said the newest oils for gas engines don't have the anti-wear additives partly because they don't need them. Most late model gas engines use roller lifters or cam followers, rather than the older style lifters or followers that more or less slide on the lobe surface of the cam (hopefully cushioned by a nice layer of protective oil!). The article said there had been a lot of problems with camshaft and lifter wear on some of the aftermarket high performance camshafts, which used the conventional flat tappet lifters. They recommended using the diesel rated oil, which continues to include the anti-wear additives, to prevent premature cam wear. I had been using whatever was on sale in 20W50 in my old Ford 641D, which leaks some oil and probably has over 10K hours on it. I always had better hot oil pressure with the 20W50 and since it was being dumped on the ground, I was trying to get by as cheaply as possible. Before I read the article, I had never had it explained why it was important to use diesel rated oil. My 641D will get Rotella at each oil change from now on, although I will probably use up the gas engine rated 20W50 I already have when I need to add oil, at least sometimes. I expect to need to rebuild or overhaul the engine in the 641D in the next few years. Hopefully the existing cam and lifters will not be worn too much to reuse, as I have heard that the diesel camshafts are hard to come by. I think I will use diesel rated oil in my 84 Ford pickup with 460. I am sure it uses conventional lifters and only has about 35K on a rebuild. I would sure hate to have the camshaft go bad on it. It will probably stay with me the rest of my life, gas hog or not. I need a hauler sometimes and the old Ford does that well.
Replies:
Home
| Forums
Today's Featured Article -
The Fordson F Ignition System - by Anthony West. A fellow restorer contacted me earlier this year asking for some help and advice on a model F that he was restoring. He had over a period of months spent a fair amount of his hard earned cash on replacement parts for the old "trembler" ignition. Sadly though all his efforts seemed to be a waste of time and money as he still couldn''t get the temperamental old thing to run correctly!! If i said that this was a little frustrating for him that would be "conservative" in fact the problem had reduce
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|