Tractor Talk Discussion Board |
Re: 782 with 822 corn head
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Weldon K on September 28, 2006 at 19:14:07 from (67.141.244.220):
In Reply to: 782 with 822 corn head posted by PJBROWN on September 28, 2006 at 15:41:51:
The 822 had a poor design in that there were no gathering chains down the side of the snouts to bring in leaning or downed stalks. Also, the stalks were cut off by the rotary knives before the gathering chains even grabbed them. If one is operated on level land and the operator is able to keep it perfectly on the row, then they can do an acceptable job. But if used on hillsides and they got off track of the row a little, stalks were knocked down and lost. I think New Holland had the 822 in production for only a year or so. They must have heard from a lot of customers about problems because the 824 replaced the 822 in short order. The 824 was a big improvement in that gathering chains go down the sides of the snouts to pull in leaners and all stalks are grabbed before they are cut off by the rotary knives.In my area 822 heads were traded in quickly for the 824. The 822's then sat on the yards for years and were never sold. I have had an 824 head for 5 years on an 880 harvester. It replaced the 880R2 which was worn out. In thick,heavy, tall corn , there can get to be such a pile of stalks and big ears being delivered into the throat that they back up and the feed rolls only spin on the ends of them and won't pull them on through, even with the high speed header drive gear installed. This I believe to be an inherent problem of this "low profile" style head. Never had it happen in the old style head. Only solution is to drop down a gear and slow tractor's ground speed. I really think that the old style two row heads (717 and 880 ) did a better job at picking up downed stalks. If the old style head had the rotary stalk knives, I would rather have it than the 824. I have used the old style two row head to harvest drill seeded sorghum-sudan hybrid and it gathered practically all of it . I do not think that the 824 would do nearly as well.
Replies:
Home
| Forums
Today's Featured Article -
Product Review: Black Tire Paint - by Staff. I have been fortunate in that two of my tractors have had rear tires that were in great shape when I bought the tractor. My model "H" even had the old style fronts with plenty of tread. My "L" fronts were mismatched Sears Guardsman snow tires, which I promptly tossed. Well, although these tires were in good shape as far as tread was concerned, they looked real sad. All were flat, but new tubes fixed that. In addition to years and years of scuffing and fading, they had paint splattered on
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|