Tractor Talk Discussion Board |
Re: Farm Dump Truck and DOT
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Billy NY on November 25, 2006 at 04:55:26 from (205.188.117.14):
In Reply to: Farm Dump Truck and DOT posted by M Nut on November 25, 2006 at 04:34:40:
A tandem dump with air brakes, I'm not sure how farm plates in MN, may change things, and maybe I am wrong, but if you are over 26,000 lbs on the gross vehicle weight, I'd have to say you need at least a class B CDL. On the inspection, besides what the law may require, you had best make sure those brakes are in good working condition and properly adjusted, fil, gravel, crushed stone and similar materials, depending on moisture and density of the aggregate, can be quite heavy, you may not need to be heaped over the sides to be over. No fun to haul fill with poor brakes. It could be possible that you may need a D.O.T. number even with the farm plates, my neighbor runs a tandem with a big 30 yd box for grain and other things and he's up over the 26,000 lb line, so the CDL and the D.O.T. number is required, he's got agricultural plates, farm plates limit your travel and require a specified route, maybe your DMV is set up like that and I am incorrect. Best to check with them and see. One good thing is that you are out of the main path it seems, and is probably flat terrain, but still, you'll know you have a load on when hauling fill, so take care of those brakes, and don't get greedy with the loads, keep em within the limits, especially at first, until you get the feel of the truck, it's a real bad feeling to not be able to stop, with a heavy load, been there and done that. I am curious about this topic too, as I run an old F-600 for light hauling, and have just a NYS inspection, agriculture plates, it's in good running condition, but I am curious about the D.O.T. requirements, have not asked DMV here, and they told me nothing when I put it on the road.
Replies:
Home
| Forums
Today's Featured Article -
Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|