Tractor Talk Discussion Board |
Re: allis chalmers 7000 series tractors
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Amo in nebraska on December 20, 2006 at 17:47:02 from (65.123.190.71):
In Reply to: allis chalmers 7000 series tractors posted by pafreehling on December 20, 2006 at 16:03:12:
The cabs do kinda suck on the 7000 series. I have driven a few...I really liked the 7000 4x4 the trans shifter you pushed forward and back plus twisted it to put in three gears...3 up and 3 down. For 4x4 get the one with 2 mufflers dont know why but single had motor trouble. Power shift in 8000 worked just like 4020, but what little bit I know about them I think Id rather have a 7 than an 8000. Motor is easy to work on and there cheap...yes. The only bad thing that Ive seen is 2 of them with completly shot motors and one of them had bad hyd. Prevenative maintence or any maintence is the key word. These guys had none...so thats a good coomment. 8000 series...my dad has a mechanic friend who thinks if it aint green it should be shot. He will work on anything and he is picky...when he overhauls a motor every bolt is run over a wire brush. Any way he worked on an 8050? mfd and he said it was worthless. Had trouble with it starting or running or something. All I remember is that HE SAID that they had trouble with the crank shaft staying in place up front I think? Tried shimming it and etc and wound up putting a grease zerk on the front of the crank. Sounds kinda funky and I didnt see it, but I have no reason to not believe him. Plus the 8000 I drove on spring I had to either it on a 50 degree morning and you open up the door and all of the heat (A/C) goes out because 1/2 the cab is open...Kinda like the old Masseys. I kinda like the shifting for the most part (diveder) on 7000 except I drove a power shift and a 1086 was a heck of a lot better than that thing...might of just been a bad one. Just my experince
Replies:
Home
| Forums
Today's Featured Article -
The Ferguson System Principal An implement cutting through the soil at a certain depth say eight inches requires a certain force or draft to pull it. Obviously that draft will increase if the implement runs deeper than eight inches, and decrease if it runs shallower. Why not use that draft fact to control the depth of work automatically? The draft forces are
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|