Tractor Talk Discussion Board |
More flywheel info
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by jdemaris on December 27, 2006 at 14:43:32 from (66.218.18.243):
In Reply to: ANOTHER QUESTION posted by Dave Sherburne NY on December 27, 2006 at 10:09:26:
I want to clarify what I said about no other flywheels fitting a 6.2 diesel. Actually, flywheels from several gas-engines will fit - but are still not correct - this includes small and big block chevy engines. I've got piles of OEM GM tech manuals but I've yet to find specific info on 6.2 diesel engine balancing. I don't know what year your 350 is - but a 1985 350 gas flywheel and clutch will physically fit the 6.2. As far as I can tell - the 6.2 diesel requires some external balancing via the flywheel mass - whereas most small and big block gas engines do not. The end-of-crank flange and bolt pattern though is the same for many gas and diesel engines that use the two-piece rear-main-seal. 6.2 diesels changed over to a one-piece around 1992. So - from anything I've read over the years - to be right you need a flywheel made for the 6.2 diesel and nothing else should be used even if it fits. The clutches from gas engines are not a problem, but the 6.2 is supposed to have a 12" clutch. Many gas engines use smaller clutches - which also might have something to do with the flywheel differences. GM #3991469 gas flywheel fits many SM and BB engines from 1955 - 1985 but will not take a 12" clutch. As I said earlier, there are lot of used OEM flywheels around. Also, places like Partsamerica sell new 6.2 diesel flywheels from Pioneer - # 502710. Oddly - Centerforce sells new racing-flywheels that are listed to fit 1969 small-block Chevys and also 1984 3/4 ton Chevy 6.2 diesel trucks. I have no idea what that is all about.
Replies:
Home
| Forums
Today's Featured Article -
Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|