Tractor Talk Discussion Board |
Re: Stieger Tractor Vs John Deere
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Hugh MacKay on January 05, 2007 at 15:51:07 from (209.226.247.48):
In Reply to: Re: Stieger Tractor Vs John Deere posted by massey333 on January 05, 2007 at 14:29:42:
My experience with articulateds goes back 30 years. I bought a new Farmall 1066, and my heavy use was pto forage harvester. Over the years it was dynoed 3 time and always turned out 150+. My tillage tools were not excessive load for 1066, 25'cultivator, 20' disk and 5 bottom plow. after 10 months of wheel tracks I didn't particularly like, I dumped the chloride and added duals. That cured the wheel tracks, but the duals sure beat the hell out of that mickey mouse front end. I had a 500 acre woodlot, (softwood spruce) had always used 300 and 560 in woodlot over the years, but workplace safety folks were pushing hard on ending that. Since I no longer had time to personally operate tractors in the bush, I purchased a Deere 540A forestry skidder, roughly 100 hp, 8 speed power shift and articulated. In winter I used it in forest, and in summer it became my favourite horse for tillage. Also used it to push and pack silage. I always marveled at how much easier that machine handled disk and cultivator and with a lot less fuel than 1066. If I had it to do again it would have been self propelled forage harvester and no 1066. Bear in mind I already had a 560D and 656D, quite capable of all other work I needed done, and I might add the most efficient tractors I ever owned. Looking back, of roughly 20 tractors, skidder, etc. i own over the years, my most economical hp was 560D, 656D and that Deere. I don't even put that 1066 in the top 10. In the past three years I've had the opportunity to operate some quite heavy and new iron. Big hp conventional front drive tractors as well as articulated CaseIH, New Holland and Deere. While I don't have any cost comparison, I can readily see these big articulateds are doing the work for a fraction of the cost of conventional tractors.
Replies:
Home
| Forums
Today's Featured Article -
Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|