Tractor Talk Discussion Board |
Re: Load rating on I-Beam
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Billy NY on January 09, 2007 at 23:16:41 from (152.163.100.74):
In Reply to: Load rating on I-Beam posted by 4020 on January 09, 2007 at 18:30:00:
One of the A.I.S.C. manual of steel construction, A.S.D. (Allowable Stress Design, or the Load & Resistance Factor Design L.R.F.D. might help you after you determine the shape, the letter designates the shape say like a "W" then the web is next say 12, then the last number designates the weight per foot, so a W12 x 26 is a W shape, has a 12" web and weighs 26 lbs. per foot. I have not looked at any of these in a few years, since I left the hustle and bustle of the high rise building cosntruction industry, but they are good reference books, when you need to know something about steel construction.
If you intend to span something with this beam, and it has to carry a load, I have always been of the opinion that an engineer should look at the details one proposes, to insure that it's ok for the loads imposed on it. It's safe practice and they range from $50 to $100 an hour around here, should not take long to analyze a straight forward detail if all the components are give.
I should refrain from lecturing or pontificating here, but it's important to know for safety reasons, I spent good part of my career, fixing details that did not work in the field, using my knowledge and reference materials, to revise things per field conditions or suggest details for things overlooked in design, that arise in the field during construction, mostly connections and fasteners but also some significant spans, in some instances, all of which were always approved, signed and stamped by a qualified licensed professional engineer after analysis. You might find an edition of those manuals in the local library and it may shed some light on what you are dealing with, am curious what you are building as well. I see editions on e-bay quite often, older ones are affordable, newer ones are $200 or more.
Replies:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|