Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: OT - Post Beam barn rework


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by jdemaris on January 12, 2007 at 06:52:59 from (69.67.229.131):

In Reply to: OT - Post Beam barn rework posted by Jon (IN) on January 11, 2007 at 11:41:16:

You didn't post any photos of the upper section where the rafters are. I've had fix many post & beam barns - I still own two that were built 1820-- 1850. The house I live in is also mortise and tenon and was built 1820. Although most of these old barns have almost non-existant foundations other than a few rocks piled on the ground, the area that usually does them in is up above. A gable-two-pitched roof puts tremendous outward pressure on the top-sides of the barn. I.e., the bottom of the triangle bellies out as gravity pushes vertically down on the ridge-peak. Something must be there to serve as a "collar-tie." Most of these older barns were held together with a few wood pins at these points. And, most pins, along with the tenon joints rotted out years ago. So, sideways cabling is the easiest and safest. 3/8" cable between each set of upright beams works fine. If this is a "one man" operation, this is how I do it. Wrap something protective around the top-upright where you are going to loop the cable around. Otherwise it will cut into the wood. If the wood is gone or rotted, scap some new wood in. Then, after the cable is looped around it and fastened with a couple of bolt-on cable clamps - run it sideways to the opposing upright on the other side. Loop the cable around and then part way back (maye half-way) and put a temporary loop on the end. Then, hooked a come-along to that loop back to the first top-post you were working on. Then, crank the cable tight - or beyond tight if the barn-sides need to be drawn back in to a certain point. When it is where you want it - just install some double cable-clamps and then cut off the remains of the cable (or just leave it if you want).
Of course - use some common sense. It won't be fun if the barn comes down with you in it.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Listening to Your Tractor - by Curtis Von Fange. Years ago there was a TV show about a talking car. Unless you are from another planet, physically or otherwise, I don’t think our internal combustion buddies will talk and tell us their problems. But, on the other hand, there is a secret language that our mechanical companions readily do speak. It is an interesting form of communication that involves all the senses of the listener. In this series we are going to investigate and learn the basic rudimentary skills of understanding this lingo. ... [Read Article]

Latest Ad: 2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy