Tractor Talk Discussion Board |
Re: Some Truck Terminology Please
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by RodInNS on March 23, 2007 at 06:49:26 from (142.177.41.195):
In Reply to: Some Truck Terminology Please posted by uncle on March 22, 2007 at 19:23:49:
Hendrickson is a walking beam set of axles suspended on one set of extended leafs. Good to keep things lively in the seat.... Camelback is an exlusive Mack suspension. The spring is shaped like a parabolic arch, and is attached to a pivot tube in the middle. The spring is the walking beam. They have a LOT of travel. Around here, they're noted for being exceptionally tough. Tough on the driver, tough on tires, and tough to break. It's a real kidney shaker of a system unless you run overweight all the time. Almost need to in order to smooth it out and hold the tires on the road.... I'm not familiar with Hotchkins. Chalmers is a common builder of rubber block suspension. They mount a couple rubber blocks between a walking beam and the frame. Drives like a camelback on steroids.... If it was me, I'd go with air ride, all the way. My preference would be Holland Newway if I could get it. International seems to have a good air ride too (at least I haven't broken it yet). Freightliner's Airliner system would be last on my list I think (in terms of air ride). I had one, and ti rides nice, and carrys well.... but I've broken several springs with it, and know of other newer trucks with that system doing farm pickups (working in farms yards, tight manuvering etc), and they've broken those systems. Airliner uses an air bag on top of a spring, and the spring is responsible for tracking the axle, and those springs break under thrust. THat's what i've found anyway. The IH system uses round bar for a track rod, and Newway uses a tubular underslung arm. I think there's a lot more strength in that system. However, given a choice, I'd take any air ride over any of the devils you listed above. There's no way I'd go back. Air Ride simply rides so smooth...... Rod
Replies:
Home
| Forums
Today's Featured Article -
Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|