Tractor Talk Discussion Board |
Re: IH guys help
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Owen Aaland on March 29, 2007 at 16:20:32 from (65.165.246.14):
In Reply to: Re: IH guys help posted by TMay on March 29, 2007 at 14:58:21:
The power steering circut is a priority circut. Nothing you do should cause any change in steering function. Oil is drawn from the bottom of the rear housing, through the hydraulic filter, through tubes cast in the clutch housing, to the steering (MCV) pump. From the pump the oil goes first to a flow divider/priority valve. The flow divider is actually two pieces. Oil goes to an an orfice that allows 5 GPM (3 GPM on 66 and older series) priority flow. Excess fluid is diverted by the flow divider valve to lube the differential. This flow varies with pump speed and condition but the 5 GPM remains constant. A worn pump or a serious leak will cause this flow to diminish to the point where no flow will go to the differential. This is the major cause for rear end problems in IH tractors. The 5 GPM flow from the flow divider goes first to the steering system and then steering relief valve. This limits the steering pressure to 1600 to 2100 PSI, depending on the tractor. Return flow from the steering and/or steering relief valve is still 5 GPM. One GPM of this flow is used to lube each brake, leaving 3 GPM for the TA control valve, brakes, seat, and hydraulic clutch assist. Pressure in this circut is limited to about 240 PSI. The TA, clutch, brakes and seat are all closed center valves that use oil only while being operated. Oil left from this circut is directed to the TA lube circut. It is limited to about 20 PSI. Any oil above the 20 PSI is returned back to the sump. Loss of steering while the clutch is depressed can be caused by a weak pump or leak AND a stuck flow divider valve. Any loss of steering assist can be an indicator that the differential is not being lubed properly. It is critical for the steering to function properly to get long life out of the differential and ring gear and pinion.
Replies:
Home
| Forums
Today's Featured Article -
Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|