Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: O/T Engine Overheating


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Howard H. on April 23, 2007 at 07:33:21 from (156.110.78.2):

In Reply to: O/T Engine Overheating posted by Ken-in-K on April 23, 2007 at 07:19:11:


Others will probably have a more direct idea, but I know I've run a bunch of irrigation motors in the past - 454's, 350's, Ford 534 V8's, MM HD800's etc.

One time I had the local repair shop overhaul a MM 800 inline 6 to run on natural gas. The engine ran great, but the exhaust manifold was so exceptionally hot, I could barely get close to it to pour oil in it. You could see it glowing from a half mile away at night.

Like I said, I've run a bunch of engines and this one was off-the-scale hot.

After a couple of months of 24x7 operation, the engine thrashed (galded piston) - the repair place said it was my fault, so I disgustedly started tearing it down to repair it myself. The oil inside had been baked into asphalt that I had to chip off with a chisel.

After I got a piston out, I carefully was checking the rings, when I realized they were installed UPSIDE DOWN! I pulled all the pistons - covered in tarry asphalt, and they all had been installed wrong. I took them over to the repair shop and the owner scrambled from one book to another, the instructions that came with the rings, etc, and finally agreed they were installed incorrectly.

They wound up rebuilding the engine for me for free and it was fine after that (and we are still friends).

I can't explain why upside down rings would make an engine act like that - and I'm not even sure that it was cause and effect. But that was my experience.

I wonder if your engine might have a piston or two with the same condition.

Howard



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga ... [Read Article]

Latest Ad: 1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952 [More Ads]

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy