Tractor Talk Discussion Board |
Re: question about king cutter
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Jerry/MT on May 19, 2007 at 15:04:06 from (206.183.116.129):
In Reply to: question about king cutter posted by daniel in sc on May 19, 2007 at 07:07:59:
Two years ago, I bought a 6 foot KingKutter with a 60 HP gearbox and a slip clutch drive line after looking at the Wood's line. I had a 5 ft Brush Hog Squealer previously. You need to know that threre are several different "lines' of KingKutter. The one I bought was a KingKutter 5 Point model.(According to the dealer they are made a bit better then the yellow units you see at the farm & ranch stores and have a brown paint job.) With chain guards front and rear it cost me about $1125 and that included the shipping. It weighs around 725 pounds. A similar model Wood's was over $2000 with guards and weighed about 675 pounds as I recall. I use the mower to do some rough cutting around the pastures and around the ranch outbuildings. I just didn't see the value in the Woods and I know many Woods owners would disagree with me, but that's the way I see it. I had a Brush Hog before and I didn't think that it was any better or worse than the KingKutter. These things are not the Space Shuttle and are relatively simple devices. The Woods looks like it has a hydroformed deck that allows it to run with out welded stiffeners and the clippings and chaff wash off easily. Hydroforming is an expensive process but it's a one or two step process whereas a weldment has a high part count and takes more assembly time. I don't know how long my KingKutter will last in my type of usage but I'm betting it will last everybit as along as the Woods, and at about one half the initial cost. Anyway, that's how I voted with my $'s. Opinions are like belly buttons;everybody's got one! This is mine regarding rotary cutters.
Replies:
Home
| Forums
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|