Posted by JoshuaGA on January 24, 2008 at 15:18:22 from (74.244.197.228):
In Reply to: ITS HERE!!! posted by Rob in Indiana on January 24, 2008 at 14:51:34:
Lanse said: (quoted from post at 07:51:34 01/25/08) and has a ton of other parts with it!! Real nice guy i bought it from, thanks Kyle!!
I pulled a plug and some kerosine came out. Does this mean?.....
Regardless, i found a carb and possibly a mag, and a muffler for it. First question, how does the muffler attatch to the mainfold??
Second question, where would i find a seat cushion and bottom, the frame is allready there.
Third question, How should i loosten up the brake levers that are apperentally rusted in place? I guess penetrating oil for em'
Forth question, how do i know when its loose if it is loose right now??? Im planning to jack it up so all the weight is on the crank and it should pop and the front end will land on the ground.
Fifth question, The shifter is a little stiff, how do i correct that?? Should be alot easier. Is it just thick oil?? Should i replace the tranny oil??
sixth question, There is rust in the gas tank. Should i somehow remove it???
Seventh question, Yall want some pics??? :-)
Eight question, have 2 additional Torque tubes for a B one of which has a starter hole on it Anybody interested?? Make an offer.
Kerosene means that they were trying to soak the motor loose.
#1. Slips on and probally clamps down.
#2. Online. Try the store here.
#3. Spray on the penetrating oil and work them loose.
#4. If it is spinning it is loose. Make sure plugs are out and motor not stuck hard before doing the jack thing, safer bet is take the head off and free it with a block of wood and heavy hammer.
#5. Change the fluid. Probally got water in and rusted some.
#6. Take off tank and either have it professonaly cleaned or clean it yourself. Old trick is to rattle some bolts and nuts around in the tank to loosen the rust.
#7. Yes.
#8. No, no need.
Buy a book for the tractor, invest in a couple how to restore a tractor books, and ask plenty of questions.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.