Posted by Billy NY on May 17, 2008 at 10:59:24 from (64.12.117.74):
In Reply to: O/T a litte bit posted by old on May 16, 2008 at 20:24:36:
I've got that same year, K10, retired to snow plow duty, but I drove it full time for over 5 years, it too was an automatic with spicer manual type hubs, which was a lot better than the full time ones, that auto trans. went and a friend at work had a complete 4 spd set up, everything out of a mid 70's chevy farm P/U truck with about 30,000 miles on it before it rusted out. The trans lube was still clear in it, changed that out though, to 85/140 cling, and put the 4 spd in there, differentials were 270's so the speedo was off, definitely highway gears made one trip home with it and it was retired.
Matter of preference on the plugs, I can remember doing that (hotter plug) with the first engine in this truck, which had some blow by, but went back to the normal range when I put a new one in. Thermostat does need to be right, engine needs a certain temp to run the best, I've tried it without the thermostat and all that, seems to like 170-180 to run best.
Another small block chevy I had beefed up along with the auto trans, was put into a '78 vette, the one thing that impressed me about that was the inexpensive, but higher voltage Accel HEI ignition module/kit that went onto the stock distributor, it was like $100 then,'91 or so, + 8mm wires and I forget which plugs, now been warned to stay away from champion, that motor would start instantaneously in the freezing cold, and having the carb dialed in, timing and all that jazz, was probably the first time I actually got everything situated just right, something was just unique about how it started, I figured the extra ignition voltage was it. This 350 motor was in the 325-375 HP range, never knew exactly it was nothing radical just a few steps up from stock, more compression, little extra lift on the cam, had roller rockers. It actually was a screw up, someone had put dome top pistons, (compression was ridiculous) radical high lift cam, never even pinned the rockers, they would have broke loose, had them shave the domes off the pistons and tone everything back down to something reasonable that you could drive, long story, some genius thought the more radical the better, thing would have come apart when I got it.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.