Posted by billonthefarm on April 16, 2009 at 18:44:31 from (205.161.2.144):
I finished checking the cows this morning about 8:30. I was in the shop and travis was helping me get the radiator back in the Versatile when my phone rang, it was 10:30. It was bud, one of the guys who sold me the cows, and he wanted to know when the yellow cow had the calf. I said I had no idea, nothing was going on at 8:30. He had his helper go out to the pasture check on the cow and calf. We talked on the phone for a minute and he said his helper was signaling him to come out and that it looked like something was wrong. Travis and I jumped in the truck and ran over there. The calf was still in the sack and they had helped him get out and momma was cleaning him up so everything was ok. We hung out there for awhile, always fun to watch just after they are born. She was busy taking care of her calf then about an hour later she layed down next to the calf. About 2 minutes later she got back up and low and behold there was another calf. I was excited but of course worried too. We stayed till about 1:30 watching them. She claimed them both, no problem at all. The first calf was a heifer and she nursed right after the second one was born but we waited and waited for the second calf, a bull, to nurse, nosed around all over but never sucked. Went back tonight when nick got here and watched the bull calf but didnt see him nurse. We put momma in the chute and put him on her but he showed no interest. I tried and tried but nothing worked. We finally decided to just wait a while and see what happened. I talked with tom, my top cow advisor, and he said if he isnt nursing we will need to move pretty quickly to keep him going. After about 45 minutes I took him over to the chute and stuck his head in there and he went to town. I guess he had his little belly full earlier because there was no doubt he knew what he was doing. Took a load off our minds wathcing that little guy nurse. Another good day on the farm. bill
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
