Posted by bc on June 17, 2009 at 15:53:51 from (69.148.27.75):
In Reply to: Rust in gas tank posted by timberwolves on June 17, 2009 at 12:42:49:
Not sure about the boiling, but when you acidize a tank to get rid of the rust, the newly clean bare metal will flash rust. There are plenty of posts here in the archives about rusty tanks. If the tank is acidized with phosphoric acid then it doesn't flash rust so bad.(sold at home cheapo in a grey container in the paint department, I forget the name)(they also have another brand but which may be cheaper but not sure of the concentration)
Even then after being acidized, the bare metal needs to be sprayed with wd-40 or some other type of (W)ater (D)ispersant of another brand. Then it can still rust again over time.
I'd take it back and see what they boiled it in and ask why they didn't treat it any further. I forget what chemical they use for boiling radiators but I believe it is a water base.
I just did the gas tank on my tiller using the phosphoric acid with water mix. Then sprayed it down with wd. I'm not sure the mix I used was very strong as I think the label said mix it 10 to 1 with water and there was still a little rust on the sides. I did my tractor tank with 2 gallons of muratic acid sitting in the bottom for a half day where most of the rust was and then filled it the rest of the way up with water for another day or two. It was shiny inside. Then sprayed it with wd. I still get some rust in my sediment bulb.
Best thing you can do is put a 1 inch or so rubber hose extension on your sediment bulb to keep the bottom dwelling rust from getting into you sediment bulb or make a screen from some brass or steel window screen or buy a screen to fit on your sediment bowl where it sticks up into the tank. I used a couple wraps of window screen the first time and held it with a piece of twisted wire around the little nubbing on the sediment bowl and stuck it into the tank. Only thing I see in the bowl now is some occasional rusty fines.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Old Time Threshing - by Anthony West. A lovely harvest evening late September 1947, I was a school boy, like all school boys I loved harvest time. The golden corn ripens well and early, the stoking, stacking,.... the drawing in with the tractors and trailers and a few buck rakes thrown in, and possibly a heavy horse. It would be a great day for the collies and the terrier dogs, rats and mice would be at the bottom of the stacks so the dogs, would have a busy time hunting and killing, all the corn was gathered and ricked in what we c
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.