Tractor Talk Discussion Board |
Re: What Do I DO Now?
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Salmoneye on January 02, 2001 at 05:53:34 from (206.27.102.82):
In Reply to: What Do I DO Now? posted by ~Flash~340 on January 01, 2001 at 21:20:52:
First off, welcome to the world of N Series Ford Tractors! Secondly, get yourself an I&T FO-4 shop manual. They are available almost everywhere including the sponsors of this board to the left. It will be the best $25 you will ever spend on your tractor. Now, as for starting it. Did you change the oil filter? It is in the round cannister forward of the starter on the left. How much oil did you put in when you changed it? The crankcase is supposed to have 6 quarts of oil. After putting in the filter, I usually pour oil in the filter cannister till it won't hold anymore. Some people say this is unnecessary, but it makes me feel better :-) Now Fuel. Remove the fuel line from the brass elbow at the carb. Turn on the gas (2 full turns for main, and fully open for the 1 gallon reserve) and see how fast the gas pours from the line. Should be a steady stream about as hard as a good healthy pee. If not, you will have to clean the screens. There are 2 at the fuel shutoff valve. One above the sediment bowl, and one inside the tank that you will have to remove the valve from the tank to get to. If you have to go this far, it is probably a good idea to flush the tank before reassembly. There is also a third screen in the brass elbow on the carb. Unscrew the elbow from the carb and clean this one too. Now Air: Remove the cup from the breather. There are 2 clips that hold it to the body. Fill the cup to the line with the same oil that you have in the engine. Pull the plugs one at a time, and put a teaspoon of oil or Marvel Mystery Oil in each cylinder. Make sure that you do not get the firing order messed up. It is 1,2,4,3 counter clockwise on the front mount distributor. Put all the plugs, and wires back and unhook the breather tube from the carb. With the fuel valve and the key both shut off, put your hand over the air intake and turn the motor a couple turns with the starter. You should feel some serious suction on your palm. If you feel suction, rehook the breather tube, turn on the gas, turn on the key, and if you have spark to those plugs, you should be good to go! If not :-( repost on the N Board and we will get you going. Here is the link for the N Board: http://www.ytmag.com/nboard/wwwboard1.html And here is a link to an excellent site to determine the year and model of your tractor.
Follow Ups:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|