Posted by ChrisLSD on November 09, 2009 at 06:11:02 from (97.114.246.194):
In Reply to: Engineered Beams posted by tlak on November 08, 2009 at 11:26:35:
to answer your question..... if the board and the engineered beam are made out of the same material (pine, fir) so they compress about the same, there load carrying capacity is the same......HOWEVER the reason modern day uses engineered beams is because if there is a structural defect in the wrong place on the lumber (let's say a knot goes from the edge in 1" on the lumber) then the lumer is only acting like an 11 board instead of a 12" board - which may not sound like a lot - but a 2X6 is 3.5 times stronger than a 2x4 on edge..... that is also why real truss manufacturing places among others use specially graded lumber which reduce these type of defects.....again depends on what kind of loading is going to happen also..... next question.... would 2 1.5" beams be twice as strong as one and be the same as a 3" beam.... basic answer is yes AS LONG AS it acts like one piece.....for example if you take 2 skinny members, place them side by side, and start loading them, if they start to seperate or lean as the load is applied then they are not acting as one unit, and will fail before the loading of the single unit that was twice as big BUT if the two skinny beams are attached together and act as one unit, then, yes they will be as strong as a single unit which is twice as thick......
Another example....place a playing card like a bridge, supported on each end.....pressing down in the middle will act as the load.....if you use more cards it will hold more load, BUT if you take a whole deck of cards and place them on this made up bridge you can still press down in the middle and make the whole deck of cards curve or deflect downward, because they are not acting like one unit.....now take that deck of cards and glue each card to the one below it so when you are done the whole deck of cards is glued together, now place that glued up deck of ards on the supprots and press in the middle - it will hold WAY more load before a significant bending or failure will occur because all the cards are acting as a single unit
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.