Tractor Talk Discussion Board |
Re: Re: Re: David Bradley Wagon
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Elden Denning on February 09, 2001 at 16:39:48 from (216.93.119.242):
In Reply to: Re: Re: David Bradley Wagon posted by JohnG(TX) on February 09, 2001 at 13:48:39:
Hi Again! Yeah, the Sears tags were usually where you found yours. Here in Hillsdale Co., MI where I live, Wards "Lo-Load" wagon trucks(or chassis, I guess you could say) were more popular but there were some Sears around. The racks here had stake pockets at the ends of the two main bed pieces that held vertical 2 X 4 uprights whatever length the standards were high plus what went into the pocket, short ones for grain use and 5-6 foot ones for hauling hay-straw-fodder-etc. Sides for grain fit into a vertical slot on the ends of the short grain box end standards(made with 2-1 X 2 inch cleats bolted to the ends. Down the edges of the floor a 2 X 2 or a 2 X 4 was bolted to the ends of the cross pieces which served to retain the bottom of the upright sides and to provide a sort of strong edge for the floor. Then a cross light weight chain or two was strung across the upper area of the sides to keep them from "bulging out when the load filled in". We use to build our own racks because we had a sawmill and used native rough-cut lumber for the frame pieces-usually white oak. We even built 3 chopper wagons following plans from the Gehl Co., who built the field chopper and blower we bought. Gehl furnished the hardware for those wagons too, they were a self unloading type using a winched back sliding endgate method. I sure remember fixing a lot of flat tires on those wagons until we got them all converted to 6 or 8 ply tires. The old Wards wagons stood up real well though. Well, once again I got carried away-sorry. Take care. Elden
Follow Ups:
Home
| Forums
Today's Featured Article -
12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|