Tractor Talk Discussion Board |
Re: Re: Re: Home built Log Skidder,
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Dan on February 21, 2001 at 19:44:02 from (209.196.110.82):
In Reply to: Re: Re: Home built Log Skidder, posted by Canadian Cowboy on February 20, 2001 at 09:47:47:
The trenchers that I ran had hydrostatic systems. The larger one that I ran had a hi/lo range on the transmission, hi range for road transport at about 15 mph. For trenching, the lo range is used. If you've never been around one, here's how it works. Both machines had a single joystick that controlled forward/backward, right/left steering. The farther forward you push the joystick, the faster you go. Pulling back to center not only slows you down, but provides braking also. You start the trencher and lower the stinger in the ground, while the machine is setting still. Once you get the depth you want, there is locking lever that holds the joystick from moving forward or backward, although you can still move it side to side to steer. The locking device also has a hand screw, and screwing it in applies slight forward pressure on the joystick so that the machine starts to creep forward. You start at a very slow speed, only a few feet per minute. You keep screwing the hand wheel in until you get to the point where you're moving as fast as the trencher can dig, maybe 30 feet per minute, depending on rocks in the soil, etc. Both machines I ran had small blades -- actually both had a 4 way blade - up/down and angle right/left. Everything was hydraulic, transmission, steering, braking, trencher drive, blades, backhoe. With higher floatation tires and a winch, I would think it would be a good platform for what you want to build. Both of these machines were Case-Davis brand. We also had a Vermeer trencher, but it was not in the same league as the others. It was a very clumsy machine that didn't work nearly as well. But in all fairness, it was pretty old at the time, and all of this was 20 years ago.
Follow Ups:
Home
| Forums
Today's Featured Article -
Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|