Tractor Talk Discussion Board |
Re: Re: Six or Twelve volt
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by John on March 08, 2001 at 12:15:35 from (208.0.20.140):
In Reply to: Re: Six or Twelve volt posted by John on March 08, 2001 at 09:13:12:
Here is what T.W. Cook has to say on this subject. 6 Volt or 12 Volt?The most frequently asked question is "how to I convert my Farmall H to a 12 volt electrical system?". My answer to this question is always "Why?". These tractors were designed to start perfectly well on 6 volts, and will today if you have proper cables and a good battery. The first thing to check is battery cables. The reason manufacturers went to 12 volts is not that it starts better, but that it will work fine with thinner cables which cost less. Many Hs through the years had their cables replaced with thin 12 volt cables. If you have these, you need to throw them away and replace them with big 2 gauge or better cables. Make sure that your ground cable (remember, the H has a positive ground system) goes directly to one of the starter mounting bolts and makes good connections on both ends. The make sure that the cable from the battery to the starter switch and on to the starter is also good. If your starter switch gets hot when you press it, consider replacing it too. If you have good cables and a good battery, it'll start right up. You should be able to get proper cables at Case-IH or Tractor Supply or similar places. If all else fails, get some 2 gauge welding cable and make your own, it isn't hard. Besides there being no good reason to do it, a 12 volt conversion will reduce the value of your tractor to a collector - it won't be original any more. If you go with an alternator, you'll have to fabricate a new mounting bracket because it won't fit under the hood any more (whatever you do, don't cut the hood!). So it will be glaringly obvious that it isn't original, and worse, the alternator will be sticking out to the side where it isn't protected from rain.
Follow Ups:
Home
| Forums
Today's Featured Article -
Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|