Posted by Nancy Howell on April 23, 2010 at 07:37:57 from (144.162.48.126):
In Reply to: 2-4-D Amine posted by mss3020 on April 23, 2010 at 06:08:24:
When we first started spraying, the labels would tell you how many ounces per gallon to mix. That has changed. Most products now state an amount per acre. 2-4-D should be one quart (1 qt=32 ounces or 4 cups)per acre. Read your label.
The amount of the herbicide per acre is static, but the amount of water you mix with it can vary. Our ag agent recommends at least 20 gallons per acre.
While a mix of one quart of herbicide sprayed at 25 gallons per acre may be weaker than one quart of herbicide sprayed at 20 gallons per acre, at 25 gallons per acre you are putting more herbicide on the weed. That means if you were spraying 20 gallons per acre the weeds might get 4 or 5 droplets. At 25 gallons per acre, the weed gets hit with maybe 7 or 8 droplets so even though the actual mix is not as strong, more of the mix gets on the undesired weeds. At the lower spray rate of 20 gal/acre, some weeds can be missed or not get enough to be effective.
Also, if you plan on grazing that field, be sure to read your label and find out how long after spraying you have to wait until you can graze the field. I don't remember exactly, but I think with 2-4-D you have to wait at least 10 days after spraying before you can graze the field.
If you need to graze this field right away, there are several products that do not have a wait time between spraying and grazing. We use GrazeonNext because it doesn't have any hold or wait time from when the herbicide is sprayed and when you can graze the field.
I recommend you find out who your local ag agent is and give him a call. They are very helpful.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.