Posted by Billy NY on October 04, 2010 at 17:04:18 from (74.67.3.54):
In Reply to: Re: Basement project posted by Bryan iniowa on October 04, 2010 at 06:07:11:
Well, if the super is nervous what the heck, a little extra support will keep 'er happy LOL!
Laying block is not all that difficult, just make sure to look at the layout, the courses with mortar joints and see where your height ends up, you may want to make a story pole, use a string line, level, set your corners etc. Basically place your mortar, set the block, tap down to the string line, check with a level, almost common sense.
You will probably want some vertical reinforcing from the footing or slab, #4 deformed bar is most common, you can fill that cell up to height, forget what is common spacing on those filled cells, 4'-0" O.C. or what your building code calls for, or if you were required to have plans, architect/engineer should specify, you can also use a ladder mesh, every or every other course, take a look at Hohmann-Barnard masonry accessories, all kinds of horizontal reinforcing etc.
Don't forget any electrical conduits, and similar things within the wall if applicable, same with wall penetrations. Nice to have a wet saw for the cuts to make your coursing, some just use a masons hammer. CMU/concrete masonry units come in all kinds of sizes and compressive strengths, which are certified by the mfr. Also don't forget to fill cells anywhere you need to attach something to a wall, filled cells are much stronger when using expansion bolts etc. vs. hollow cells, though you can get heavy duty CMU like 4000 psi-5000 psi, with 75% of the cells filled, which means the block has thicker and stronger cell walls. Hopefully you know someone who has some experience, really not to bad to learn, little at a time, keep your mortar mix design uniform or use a good bagged mix, should go ok. Don't make too much at one time, better to keep fresh material flowing.
Been hot and dry here all summer sounds like you guys got all the rain this year !
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Women and Tractors - Tractor Engine Repair - by Teri Burkholder. One of the great things about working on a tractor engine with your other half is that you know what he is thinking of at all times and can anticipate his every move and his next thought of what he will do. With Ben, anyway, I can tell! He'll be busy working and I’m handing him tools and he says, "give me that..." and I’ve already got it in his hand or "hand me that....."and I’ve got the portable light right where he needed it placed to see. "Run in the house and get me a...."as I open th
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
