Having worked on both farm and construction equipment most of my life I"ve got to say I agree with the reply saying the bolts in the kits will usually stay there while the empty slots will fill up with stuff you actually need. Well, may be it"s not quite that bad but even though the actual bolt sizes and thread pitches used on most machines are common they also use alot of lengths that are not included in the standard kits. By that I mean is most kits break their lengths down in 1/2 inch increments and for the most part these bolts can be used as long as there is clearance. On the other hand alot of the bolts used are needed in 1/4 increments (ie 1 1/4 long vs 1 1/2 long). If your putting a bracket on a block, etc where there is a blind hole and it"s not deep enough, your out of luck unless you can cut the end off of the longer bolt. Then you"ve got to worry that the grip length (unthreaded part) isn"t so long that it hits the threads before the bolt gets tight. You"ll usualy find this problem more prevelant in the smaller sizes, say 1/2 down but it can come into play with the larger stuff too on occasion. As far as finding the 1/4 inch increments assortments I"ve never seen it in anything off the shelf. Short of going through an industrial supplier that lets you make up the mix of fasteners offered in one of their large shop sized setups I don"t know where you"d get anything with that mix without making it up yourself.
Once you get past the standard stuff then you get into the metric and it"s even worse. With that mess you"ve got not just the lengths and thread pitches to worry about but also the head size of the bolt. For instance the same thread and pitch from one mfg might have a 14 MM head on it and from another it might have a 17 MM head on it. Then thrown in the fact they also like flange head bolts, which are often the same way, and it becomes a real nightmare.
In the end all I can say is get on the boards specific to the brand tractors you have and ask if any mechanics can tell you the most common sizes they encounter on that particular brand. For instance I know IH like"s 7/16, Detroit Diesel loves 3/8 fine thread bolts in odd lenghts, etc, etc. Figure out the most common sizes and set up something on your own as ultimately you"ll save money over buying an off the shelf kit with parts you"ll never use.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
