Posted by 135 Fan on February 04, 2011 at 22:09:58 from (68.149.56.30):
In Reply to: broke my loader. posted by 504 on February 04, 2011 at 18:59:48:
I assume you mean the pin mount mount broke off the end of the cylinder rod? Did the cylinder rods bend at all? Nothing too special to weld them as long as you know what you're doing. It's best to take the cylinders apart but can still be done with the cylinders together. You have to have the rod extended all the way and wrap something like an old welding glove or other piece of leather or non flammable material around the rod to protect it from weld spatter. First look and see if it broke right at the factory weld. That will give you an idea of how it was welded originally. It may not have been the best weld from the factory either. You need to grind the old weld off of both pieces and then grind a bevel on the rod. I'd grind a bevel on one side and then another bevel 180 deg. to the first bevel. This will be the top and bottom to weld the pin eye on. You will get more weld length wise(across the top and bottom parallel with the pin) on the pin eye than than on sides(ends) of the pin eye. You can make the bevel deeper than the original to add additional weld for more strength. Don't go to far back with the bevel on the rod. You just want enough room to get the welding rod in there for good penetration. You don't want your weld repair to interfere with the barrel of the cylinder when it's retracted all the way. If you have reasonable welding skills, 7018 should be plenty strong enough. I wouldn't use MIG or even attempt the repair if you don't have enough welding experience. You don't want to be lifting something up and have it all of sudden come crashing down cause your weld wasn't strong enough. A couple passes will be stronger than 1 pass just don't let it get too hot. Go back and forth between the 2 cylinders. Once you have it ground and ready to weld, it would be a good idea to mount the pin eye onto the bucket/fork attachment and tack it in place real good. This will ensure that the pin will line up. After putting a couple good tacks, take the pin out and and rotate the cylinder rod so you can put a couple more tacks on the other side. Then you're ready to weld it. I'd turn the rod and weld the 2 ends first. This will hold it straight so you can grind the tacks out on one side to put a pass in the bevel. Once that side is done, turn the rod and grind the other tacks out and weld that side of the bevel. I would weld the ends on one cylinder, then do the ends on the other cylinder. Then I'd put the first pass in both bevels of the first cylinder and repeat on the second cylinder. This will give it enough time to cool off a little. Then do the final pass filling up the bevels. Let it cool on it's own. One other thing I should mention is to make sure you have a good ground for the welder. I'd hook the ground on the pin eye. You don't want any arcing on the cylinder rod. Hope I made sense. It's simple to think about but hard to type what you're thinking. Dave
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - When Push Comes to Shove - by Dave Patterson. When I was a “kid” (still am to a deree) about two I guess, my parents couldn’t find me one day. They were horrified (we lived by the railroad), my mother thought the worst: "He’s been run over by a train, he’s gone forever!" Where did they find me? Perched up on the seat of the tractor. I’d probably plowed about 3000 acres (in my head anyway) by the time they found me. This is where my love for tractors started and has only gotten worse in my tender 50 yrs on this “green planet”. I’m par
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
