TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Marketplace

Community

Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info

Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Farmall Tractors Discussion Board

IH = H not firing on all

[ View Follow Ups ] [ Post Followup ] [ Return to Farmall Tractors Discussion Board ]

Posted by Joe on March 28, 1999 at 18:18:12:

I have an H that I overhalled a few years back,sence the work was done #3 clyinder does not fire when cold, after running for 5-6 minutes comes out of it. heads reworked valve setting cheched many times had wires checked and replaced same with plugs works fine when warm just dont like the sound when I start it

Follow Ups:

Re: IH = H not firing on all Dexter 19:17:56 4/01/99 (0)
Re: IH = H not firing on all The Red Again 06:47:00 3/29/99 (0)
Re: IH = H not firing on all RK Smith 04:38:08 3/29/99 (0)
Re: IH = H not firing on all The Red 02:25:46 3/29/99 (1)
- Re: Re: IH = H not firing on all mjdelaney 04:31:59 3/29/99 (0)

Post a Followup

Name:
E-Mail:

Subject: Re: IH = H not firing on all

Comments:

Optional Link URL:

Link Title:

Optional Image URL:

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Today's Featured Article - Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t ... [Read Article]

Latest Ad: 2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy