Farmall & IHC Tractors Discussion Board |
Re: Re: Re: Re: Re: IH-6
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Wardner on December 31, 2002 at 22:10:51 from (67.25.169.253):
In Reply to: Re: Re: Re: Re: IH-6 posted by Ron In NE on December 31, 2002 at 18:47:16:
Denny Frisk knows more about the Elwood than I do. He worked in the IH assembly plant where they were installed on tractors built after my 660. I think that you will find some of his posts, as well as mine, by typing in Elwood in the search box. I believe the earlist Elwoods were manufactured in the early fifties. Probably about the same time that Harrington started puting fwd under Ford Trucks. There was probably an appreciation and demand for these vehicles when the GIs came home from the war. Surplus axels became available at that time as well. The axel on my Elwood looks like a unit that might have fit a Dodge M-38 or deuce-and-a-half. The transmission for the fwd attaches to the belt pulley opening on the rear frame lid. It is driven by the pulley gear located on the main shaft. It will operate in all five gears (10 with TA). It can be selected to operate or not operate with a sliding gear. It will fit any "M" through 660. I believe the first units were sold to IH dealers or direct to farmers. Later units were sold to the factory. My tractor was bought at auction for $2800 about five years ago. Even though it ran well and had good paint, the bidding was not very spirited. Several used equipment dealers were in attendance and bidder numbers were probably in excess of 400. It was used in a hilly apple orchard 10 miles west of Rutland VT. It pulled a spray rig and had a homemade cab which I have taken off and replaced with the big curved fenders that fit that model. I know of several others. I have seen pictures of probably 10 more. I would guess that there are probably several hundred still about. The tractor is unusual but not rare enough to expect a large premium at resale. I took it to one tractor show and it didn't draw much interest.
Follow Ups:
Home
| Forums
Today's Featured Article -
Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|