Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

Re: Tractor hauler update.


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by FC on August 26, 2003 at 05:25:49 from (66.84.205.26):

In Reply to: Tractor hauler update. posted by Kelly C on August 25, 2003 at 17:43:22:

Good looking trailer there Kelly. I have a little story to tell about a "bought" trailer. A couple years ago I decided to purchase a 16 ft bumper pull trailer (7,000 lb rated with self storing ramps) to haul my C and 8N ford on, and whatever else I might need to haul. The first time I tried to load the trailer I pulled my C on the ramps I noticed the fenders "pull" away from the side rails. My attention was drawn away from the fenders by the fact my tires were set too wide to load anyway so I backed off the ramps and loaded the 8N and brush hog as I had some mowing to do at my other place. Again I noticed the fenders pull away from the side rails. To make a long story short I basically bent the side rails in a rainbow due to the weight of the tractor on the very rear of the trailer when loading. To make a long story short I took the trailer to the manufacturer and they replaced it with a much heavier built one, but told me I should support the rear when loading with ramps (I probably should). My argument was that it included loading ramps and no support for the rear nor did anyone mention to only use the ramps when supported and my load did not get close to the 7,000 lbs the trailer was rated for. The original trailer was made from 3X5X1/4 angle on the sides. The one they replaced it with is made with 4X6X3/8 angle and welded much better. I have loaded it without support and it does not give, but I probably would not load an M on it. Bottom line is some manufactured trailers are very weak, but I did get a decent built trailer in the end for approximately $1100.


Follow Ups:




Post A Followup

:
:

: Re: Re: Tractor hauler update.

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Identifying Tractor Noises - by Curtis Von Fange. Listening To Your Tractor : Part 3 - In this series we are continuing to learn the fine art of listening to our tractor in hopes of keeping it running longer. One particularly important facet is to hear and identify the particular noises that our ... [Read Article]

Latest Ad: 1997 cub cadet 7275 compact utility tractor 4wd hydro trans cracked block 3500 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy