Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Farmall & IHC Tractors Discussion Board

C Clutch Issue Resolved (mostly)


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by David in UT on November 07, 2003 at 14:08:49 from (208.15.63.194):

All,

Some of you may recall my posting from a week or so ago in which the clutch on a rebuilt '50 C seemed like it wouldn't disengage fully...

http://www.ytmag.com/farmall/messages/388058.html

Well, I have new results to report! (Most of 'em are good...)

Big Don was right. When I blew the installation of the first engine, I bent the clutch disk. It was pretty clear once I got it out. I installed a new disk, made sure I had greased the pilot bushing, and put the tractor back together again. The clutch now works great!

For those interested, I've uploaded a couple of pictures of the bent clutch disk:

http://home.earthlink.net/~farmallfan/images/bent-clutch1.jpg
http://home.earthlink.net/~farmallfan/images/bent-clutch2.jpg

It was bent to the extent that the inside hub was rubbing against the flywheel bolts.

The bad news is that, in addition to the clutch disk, I bent the drive shaft too. Not a lot, but enough so that I could see the end bounce around when I had a neighbor rotate the PTO shaft. I can feel the vibration at higher RPMs... So, I'm now noodling over whether or not I want to find another shaft and swap it out. Anyone know if I have to remove the clutch housing from both ends in order to do that?

So, thanks for everyone's input -- the C is back in business! (And, I'm getting really much better at putting a split tractor back together the *right* way.)

- David




Follow Ups:




Post A Followup

:
:

: Re: C Clutch Issue Resolved (mostly)

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Cletrac General GG and the BF Avery A - A Bit of History - by Mike Ballash. This article is a summary of what I have gathered up from various sources on the Gletrac General GG and the B. F. Avery model A tractors. I am quite sure that most of it is accurate. The General GG was made by the Cleveland Tractor Company (Cletrac) of Cleveland, Ohio. Originally the company was called the Cleveland Motor Plow Company which began in 1912, then the Cleveland Tractor Company (1917) and finally Cletrac. ... [Read Article]

Latest Ad: 1997 cub cadet 7275 compact utility tractor 4wd hydro trans cracked block 3500 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy