Farmall & IHC Tractors Discussion Board |
Re: cabs on '66 series tractors
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hugh MacKay on December 15, 2003 at 06:37:25 from (209.226.247.87):
In Reply to: cabs on '66 series tractors posted by Bryce Andreasen (Magnum) on December 14, 2003 at 19:50:23:
Bryce: There are a number of factors at play here. The number one in my mind is safety. The red cab with straight doors is a ROPS cab, whereas the Excell or white with the door angled in at bottom is not a ROPS cab. If a roll over occured with a non ROPS cab you are almost certainly going to be history. At least with the open station tractors, you did have chance, all be slim, of jumping clear. I can remember a purchase of several 1066 by one customer all in one sale. They were ordered with ROPS cabs. When the tractors came in to dealer they all had the non ROPS Excell cab. The customer refused to take the tractors. IH had to change all of them to ROPS cab. I bought one of those Excell cabs from IH for $500. and modified it a bit to fit my 656. I was always very concious of who I let drive that tractor. Since my farm was quite flat and that tractor did mainly haybine, baling, corn planting, drilling, spraying and plowing I considered the risks and acted accordingly. I did have a 1066 with the ROPS cab at the time. Cab gets you spoiled, and since hired help was doing most of the 1066 jobs ie forage harvester, manure spreader, field cultivator and disk. I couldn't see me setting out in cold on 656. I agree very much the Excell is a much more attractive cab, easier to see the work around you and yes even easier to get in and out of. As to why a lot of these cabs are coming off air packs up, heater the same, insulation is falling appart, dirt is penetrating the cab, etc. One thing about the old open station tractor, the dust may hit you but at least it blows away. I can remember baling hay for example 560D open station was my tractor of choice, even when the other two were idle.
Follow Ups:
Home
| Forums
Today's Featured Article -
Fabrication (Who Me? Make it myself?) - by Chris Pratt. First of all, what are the reasons for not fabricatin your own parts? Most judgements on what should be purchased rather than fabricated stem from: Originality - If the tractor restoration is to be 100% original, it is likely that you should spend the time and money to locate the component in the used or New-old-stock market. Since this can be extremely difficult, you may want to fabricate the item or purchase a modern replacement temporarily, but eventually, you s
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|