Farmall & IHC Tractors Discussion Board |
Re: Farmall Super A ? change 6 to 12 volt
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steve W (NY) on August 26, 2004 at 06:17:18 from (24.213.210.222):
In Reply to: Farmall Super A ? change 6 to 12 volt posted by Myron Schmidt on August 25, 2004 at 22:02:43:
My take on it is this. Tractor is what....40 years or more old? It got along this long on 6V, why change it? Here's what to check to make it work for another 40 years. 1 Guage Battery cables. These are often replaced with 12V skinny cables. You can usually find that during cranking, some part of the wrong cable will get hot. That's telling you that they need to be replaced. Second thing is you need to make sure all the connections are "clean, bright and tight". After I clean everything, I always smear a little dielectric grease on the connections. Some people swear by vaseline. Either way, it will prevent corosion from setting in. If it doesn't charge, diagnosing is pretty easy, and it will be cheaper and easier to find the problem than replace it with a 12V system and rewire it. Finally, this may not be true for everyone, but I like my stuff "factory". If I see a machine that's been modified, I always figure it's worth less. That goes for 12V conversions, no matter how well they are done. One last thing. If you have a good battery and good cables, and you don't use your lights, you don't even need a working charging system. Get a "Battery Tender" brand battery charger. This isn't a trickle charger, it''s one that shuts itself off when the battery reaches full charge. You can run a Super A all day on a good battery, and just plug it in at night. Both my BN and Ford 2N I have purposely undercharging. I plug whichever one I used last into the charger, and the batteries never get overcharged, which is the leading reason for worn out batteries in these old tractors. The 2N's battery came with the tractor 5 years ago and is going strong. They will both start right up at -20 degrees Farenheit. Take Care Steve
Follow Ups:
Home
| Forums
Today's Featured Article -
Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|