|
Farmall & IHC Tractors Discussion Board |
We're on a roll now
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Tom in PA on November 24, 2004 at 10:42:18 from (164.156.136.160):
In Reply to: Re: Purchasing my first antique tractor posted by SAm in NS on November 24, 2004 at 07:44:59:
Okay - I understand the idea behind the live PTO now... so -- when I'm looking at the M models that have the hydraulic lines coming from the transmission they are not a live setup right? The live hydraulic pump mounts near the distributor correct? The M model I looked at yesterday had two hydraulic style fittings coming out of one side of the belly and one coming out the other. Can someone explain how these setups work please? Also - I looked at a Farmall 450 gas. It had the TA and I think it had a 3pt hitch too. The only thing that concerns me about that is the TA. I've been lurking around on the board here and reading about TA's on the net. I understand that if you operate them improperly you can be talking about a serious amount of cash... how exactly do these work? I really like the M w/ the wide frt, but I don't want to have to spend a ton of cash to make it do what I need... We were talking about the scrape blade. One of you mentioned there are no control arms on the M. If I purchased the 3pt conversion there would be - correct? But then I'm also going to need the live hydraulic pump and related servos/lines so that I have both lift and downforce - right? You guys are right - I am asking a bunch of questions, I just want to make sure that I am doing the right thing here. Since I bought this land I have to sell a 1979 IH Scout II that I spent 3 years doing a body-off-frame restoration on - I'm going to miss it for sure, and am looking for a nice RED tractor to take its place. I realize the Ford may be more practical, but it isn't an IH. I know in this forum you gentlemen understand that.
Follow Ups:
Home
| Forums
Today's Featured Article -
Tractor Profile: Earthmaster - by Staff. This tractor, manufactured by the Earthmaster Farm Equipment company in Burbank, California was made for only two years. The Model C came out in 1948 and was followed by the "CN" (narrow-width model), "CNH (narrow-width high-crop model), "CH" (high-crop), "D" and the "DH" (high-crop) in 1949. The main difference between the models was tire size, tractor width and cultivating height. The "D" series were about 20 inches wider overall than the
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
