Farmall & IHC Tractors Discussion Board |
Re: Best tractor to round bale
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hugh MacKay on July 14, 2005 at 13:45:08 from (209.226.106.125):
In Reply to: Re: Best tractor to round bale posted by John Hobby on July 14, 2005 at 03:56:38:
John: I never meant to suggest your bales were costing a $100. per bale. Just using that as a figure of speech, in suggesting we try and keep the costs low. I went with a silage feeding program in the mid 1960s. I did it mainly because was putting up 35,000 small square bales per year with bale thrower and wagons. I was also competing for labor used to getting 3 times what we could justify on the farm. every year it got harder and harder to find that labor. Haylage was not cheap feed although it was excellent quality I first went with 560 and a NH S-717 harvester, too slow. Then the big guns, 1066 and NH 890. Yes, I've seen 1066 fill a 24x70 silo in 24 hours, but you had to keep pickup with fuel tank right in the field with it. In essence what I'm saying, had big roll balers come 10 years sooner, there would never have been silos or a 1066 on my farm. It took 656 on haybine round the clock to keep 1066 going. If I did the same round baling, 560 would bale it all up in about 6-8 hours per day. And yes I had a few hills, not many, about 80% of my farm was flat. I couldn't see where round baler and bale bothered 560 on the hills very much. Lets face it baler and bale wouldn't weigh 2.5 ton. I've seen it roll in my driveway pulling 6-7 tons of silage wagon in 4th and that was as steep as any farm field I've been on. If you want a pull for a 1066, try a dead highway tractor trailer up a 30% grade grossing 78,000 lbs., raining and on grass. Low 4th, high on the TA. I admit it just started raining as we tarped the load of grain. That load of grain had to come up that hill before it got too wet, as grain had to go to a dryer.
Follow Ups:
Home
| Forums
Today's Featured Article -
Identifying Tractor Noises - by Curtis Von Fange. Listening To Your Tractor : Part 3 - In this series we are continuing to learn the fine art of listening to our tractor in hopes of keeping it running longer. One particularly important facet is to hear and identify the particular noises that our
... [Read Article]
Latest Ad:
1997 cub cadet 7275 compact utility tractor 4wd hydro trans cracked block 3500
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|